Lincoln Corsair: Tire Sealant and Inflator Kit (IF EQUIPPED) / What to do after the Tire has been Sealed
After using the kit to seal your tire, you will need to replace the sealant canister. Sealant canisters and spare parts can be obtained at an authorized Ford dealer. Empty sealant canisters may be disposed of at home. However, canisters still containing liquid sealant should be disposed of by your local authorized Ford dealer or tire dealer, or in accordance with local waste disposal regulation.
Note: After the sealing compound has been used, the maximum vehicle speed is 50 mph (80 km/h) and the maximum driving distance is 120 mi (200 km). The sealed tire should be inspected immediately.
You can check the tire pressure any time within the 120 mi (200 km) by performing the steps listed previously in the Second stage: Checking Tire Pressure procedure.
Removal of the sealant canister from the kit
- Unwrap the dual purpose hose (black
tube) from the compressor housing.
- Unwrap the power cord.
- Remove the back cover.
- Rotate the sealant canister up 90 degrees and pull away from casing/housing to remove.
Installation of the sealant canister to the kit
- With the canister held perpendicular to the housing, insert the canister nozzle into the connector and push until seated.
- Rotate the canister 90 degrees down into
the housing/casing.
- Snap the back cover back into place.
- Wrap the dual purpose hose (black tube)
around the channel on the bottom of the
housing/casing.
- Wrap the power cord around the housing and stow the accessory power plug into its storage area.
Note: If you experience any difficulties with the removal or installation of the sealant canister, consult your authorized Ford dealer for assistance.
Be sure to check the sealant compound’s use-by date regularly. The use-by date is on a label located on the sealant canister and can be seen through the rectangular viewing window on the bottom of the kit. The sealant canister should be replaced when the sealant expires.
Second Stage: Checking Tire Pressure
WARNING: If the tire does not inflate
to the recommended tire pressure within
15 minutes, stop and call roadside
assistance.
WARNING: The power plug may get
hot after use and should be handled
carefully when unplugging...
Tire Care
..
Other information:
Lincoln Corsair 2020-2024 Service Manual: Removal and Installation - Rear Side Member
Special Tool(s) / General Equipment Resistance Spotwelding Equipment 8 mm Drill Bit MIG/MAG Welding Equipment Spot Weld Drill Bit Locking Pliers Materials Name Specification Seam SealerTA-2-B, 3M™ 08308, LORD Fusor® 803DTM - Removal WARNING: Electric vehicles damaged by a crash may have compromised high voltage safety systems and..
Lincoln Corsair 2020-2024 Owners Manual: Breaking-In. Driving Through Water
Breaking-In You need to break in new tires for approximately 300 mi (480 km). During this time, your vehicle may exhibit some unusual driving characteristics. Driving Through Water WARNING: Do not drive through flowing or deep water as you may lose control of your vehicle. Note: Driving through standing water can cause vehicle damage. Note: Engine damage can occur if water enters the air fi..
Categories
- Manuals Home
- 1st Generation Lincoln Corsair Owners Manual
- 1st Generation Lincoln Corsair Service Manual
- Fuel Quality - Gasoline
- Auto Hold (IF EQUIPPED)
- Automatic Transmission - 8-Speed Automatic Transmission – 8F35/8F40
- New on site
- Most important about car
Audio Unit
WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle. We recommend against the use of any hand-held device while driving and encourage the use of voice-operated systems when possible. Make sure you are aware of all applicable local laws that may affect the use of electronic devices while driving.
